When you are designing components that operate in the fiery heart of a jet engine, a nuclear core, or a deep-sea oil well, regular stainless steel simply taps out. You need materials that don't blink when temperatures soar past red-hot levels while withstanding brutal mechanical stress. Enter Inconel 718 and Inconel X-750—two of the most celebrated precipitation hardening superalloys in modern engineering.
Both belong to the austenitic nickel-chromium family. Both boast formidable corrosion resistance and rock-solid mechanical integrity under heavy loads. But here is the million-dollar question: When should you pick the workhorse Inconel 718, and when does Inconel X-750 take the crown?
While they might look identical on a warehouse shelf, their internal physics, precipitation metallurgy, and high-temperature sweet spots could not be more distinct. Let’s dive under the hood to see how these two alloys behave when the thermal heat is turned all the way up.
![]()
To understand why these alloys behave so differently at 650°C, we have to look right into their atomic recipe.
┌─ Inconel 718 ──> High Nb (~5.3%) + Mo (~3.0%) ──> Primary γ'' (Gamma Double Prime)
Nickel-Chromium Base Superalloys ───┤
└─ Inconel X-750 ─> High Ti (~2.5%) + Al (~0.7%) ──> Primary γ' (Gamma Prime)
Both alloys share a strong nickel-chromium backbone (~50–70% Ni and 14–21% Cr), which gives them their legendary resistance to oxidation and chemical attack. However, their secondary alloying elements steer them onto completely different functional paths:
Inconel 718 (UNS N07718) packs roughly 5.0% to 5.5% Niobium (Columbium) alongside 2.8% to 3.3% Molybdenum. It keeps Titanium low (~0.9%) and Aluminum minimal (~0.5%).
Inconel X-750 (UNS N07750) skips the heavy molybdenum addition and relies instead on 2.25% to 2.75% Titanium and 0.4% to 1.0% Aluminum, with Niobium capped around 0.7% to 1.2%.
![]()
Think of precipitation hardening like reinforcing concrete with microscopic rebar:
Inconel 718’s secret weapon is γ'' (Ni₃Nb): This body-centered tetragonal phase creates intense localized lattice strain, delivering staggering room-temperature and intermediate-temperature yield strengths exceeding 1,100 MPa.
Inconel X-750 relies on γ' (Ni₃(Al, Ti)): This face-centered cubic phase precipitates evenly throughout the matrix. While it yields slightly lower peak tensile strength than 718 at room temperature, it enjoys much higher thermodynamic stability when soaked at prolonged high heat.
![]()
Operating Temperature Scale: 0°C ───────────────────── 650°C (1200°F) ───────── 704°C (1300°F) ───────── 980°C (1800°F) │ │ │ │ ├─ Inconel 718 Peak Zone ─┤ (Overaging: γ'' -> δ) │ │ │ │ │ │ └──────────── Inconel X-750 Extended Resilience ──┴─── Relaxation Resistance ┘
Here lies the most critical engineering distinction between the two materials:
Inconel 718 has a hard "thermal ceiling" around 650°C (1200°F). Why? Because the metastable γ'' phase begins overaging and transforming into the stable, needle-like δ (delta) phase (Ni₃Nb, orthorhombic). Once this phase transformation occurs, the alloy rapidly loses its creep strength and notch ductility.
Inconel X-750 easily operates beyond 700°C (1300°F) and can sustain moderate structural loads up to 815°C (1500°F)—even offering short-term oxidation and thermal resistance up to 980°C (1800°F). Because γ' does not transform like γ'', X-750 stays metallurgically stable at temperatures where 718 begins to soften.
![]()
Between room temperature and 600°C, Inconel 718 nickel alloy is an absolute monster. It maintains high-temperature tensile strength of roughly 1,200–1,300 MPa, vastly outperforming X-750 (which hovers around 850–950 MPa). If your application requires brute force, burst containment, or heavy structural support below 650°C, 718 is the clear winner.
| Property / Parameter | Inconel 718 (AMS 5662/5663) | Inconel X-750 (Equalized & Aged) |
|---|---|---|
| Nominal Nickel Content | 50.0 – 55.0% | 70.0% min |
| Primary Strengthening Phase | γ'' (Ni₃Nb) + minor γ' | γ' (Ni₃(Al,Ti)) |
| Room Temp Yield Strength (0.2%) | ≥ 1100 MPa | ≥ 750 - 850 MPa |
| Room Temp Tensile Strength | ≥ 1350 MPa | ≥ 1100 - 1200 MPa |
| Useful Structural Temp Ceiling | ~650°C (1200°F) | ~704°C–815°C (1300°F–1500°F) |
| Primary Failure Mode >650°C | γ'' → δ phase coarsening | Progressive grain-boundary creep |
| Weldability / Strain-Age Cracking | Excellent (Sluggish precipitation) | Poor to Fair (Prone to cracking) |
What happens when a material is held under constant tension or compression for thousands of hours at high heat?
Thermal Relaxation in Springs: Imagine a compression spring inside a turbine steam valve at 600°C. If made of 718, internal dislocation glide and microstructural coarsening can cause the spring to lose its tension. Inconel X-750 spring wire subjected to specialized thermal equalization offers world-class relaxation resistance, holding its elasticity without taking a permanent set.
Creep and stress rupture life: In rotating components under centrifugal force below 650°C (such as gas turbine engine components), Inconel 718’s fine grain structure delivers superior resistance to high-cycle fatigue and time-dependent strain.
Before Inconel 718 arrived in the 1960s, welding high-strength nickel superalloys was an engineering nightmare. Inconel X-750, strengthened rapidly by titanium and aluminum (γ'), precipitates almost instantly during the cooling cycle of welding. This rapid precipitation causes intense localized shrinkage stresses, leading to catastrophic strain-age cracking (post-weld heat-treat cracking).
Inconel 718 solves this with its niobium-based γ'' kinetics. The precipitation reaction is sluggish, allowing the welded joint to cool and relieve thermal residual stress before the hardening phase locks the lattice. You can weld 718 in thick sections, repair it, and anneal it without fear of sudden micro-fissuring.
┌─ Rotating Turbine Discs & Blisks
├─ Cryogenic to 650°C Rocket Nozzle Structures
┌── Inconel 718 Winner ──┼─ High-Strength Aerospace Fasteners
│ └─ Sour Gas Downhole Tooling (NACE MR0175)
Industry ┤
│ ┌─ High-Temp Spring Grids & Belleville Washers
└── Inconel X-750 Winner ┼─ Nuclear Core Control-Rod Springs & Grid Spacers
├─ Gas Turbine Hot-Section Static Seals & Bellows
└─ High-Heat Forming Dies & Mandrels (>700°C)
Rotating Aerospace Assemblies: Jet engine turbine discs, compressor rings, shafts, and casing rings that endure extreme inertial stresses up to 650°C.
High-Strength Fasteners & Bolting: Heavy-duty studs conforming to ASTM B637 specification.
Deep Oil & Gas Extraction: Wellbore packers, subsea valves, and drill collars requiring high yield strength combined with sulfide stress-corrosion resistance.
High-Temperature Springs & Belleville Washers: Exhaust valve springs, steam turbine seal springs, and furnace fixturing up to 704°C.
Nuclear Reactor Internals: Core holding springs, fuel assembly grid spacers, and guide-tube pins where low cobalt and relaxation resistance under neutron flux are critical.
Thermal Bellows and Expansion Joints: Flexible seals in rocket engine exhaust ducts and hot industrial dampers.
![]()
Choosing between Inconel 718 and Inconel X-750 comes down to three deciding factors: operating temperature, loading profile, and fabrication method.
If your component operates below 650°C (1200°F), requires massive tensile and fatigue strength, and involves intricate welded geometry or complex machining, Inconel 718 is almost certainly your best bet.
Conversely, if your design calls for a spring, sealing ring, or static component that must hold its elastic tension above 650°C and up to 704°C–815°C, or needs superior resistance to load relaxation in extreme thermal environments, Inconel X-750 remains the proven material of choice.
Still unsure whether Inconel 718 or X-750 fits your operating temperature profile? Contact our superalloy metallurgists for technical consultation.
Q1: Can Inconel 718 be used above 650°C (1200°F) for short durations?
While Inconel 718 will not melt at 650°C, prolonged exposure triggers the irreversible phase transformation of its strengthening γ'' precipitate into the equilibrium δ phase. This results in a sharp drop in yield strength, notch ductility, and creep rupture life. For sustained temperatures above 650°C, alloys like Inconel X-750, Inconel 718Plus, or Waspaloy are recommended.
Q2: Why is Inconel X-750 preferred over 718 for high-temperature springs?
Inconel X-750 exhibits exceptional resistance to stress relaxation at temperatures up to 704°C (1300°F) when given an equalization and aging heat treatment. It retains its spring constant and elastic recovery far better than 718, which tends to suffer relaxation and permanent deformation under sustained elevated heat.
Q3: Is Inconel 718 harder to machine than Inconel X-750?
Both alloys are notorious for high work-hardening rates and low thermal conductivity, generating high heat at the cutting edge. However, aged Inconel 718 is generally more abrasive and tougher on cutting tools due to its higher yield strength (~1100 MPa vs ~800 MPa for X-750) and molybdenum carbide content. Rigid setups, positive rake carbide or ceramic inserts, and copious coolant are essential for both.
Q4: How do the corrosion resistances of Inconel 718 and X-750 compare?
Both alloys provide outstanding resistance to oxidation, high-temperature combustion gases, and a wide range of corrosive chemicals. Inconel 718 has slightly better resistance to localized pitting and crevice corrosion in chloride-rich and sour gas (H₂S) environments thanks to its 3.0% Molybdenum addition, making it compliant with NACE MR0175/ISO 15156.
Q5: Can Inconel X-750 be welded safely without cracking?
Yes, but it requires strict metallurgical controls. Inconel X-750 should always be welded in the overaged or fully annealed condition—never in the precipitation-hardened state. Fast travel speeds, low heat input (GTAW or EBW), and rapid post-weld heating through the 650°C–850°C aging zone are required to prevent post-weld strain-age cracking.
![]()